Characterisation and Evaluation of Bast and Core Fibre of Sugarcane (Saccharum Officinarum) Bagasse for Pulp and Paper Production

Abstract: This study was conducted to determine the suitability of bast and core fibre derived from S. Officinarum bagasse (an agricultural waste) for pulp and paper making. The bagasse was chipped and macerated in a 1:1 mixture of acetic acid and hydrogen peroxide for three weeks to release the fibres. The fibre dimensions were measured under the microscope and morphological indices calculated. Physicochemical properties (ash and moisture content, cold water, hot water and 1 % NaOH solubility) were also determined using American Society for Testing and Materials (ASTM) method. The bast fibre was digested with 2 and 4 M NaOH in ratios 1:10, 1:20 and 1:30 (w/v) at pulp time of 30, 60 and 90 minutes, respectively. The mean values obtained for fibre length, fibre diameter, lumen width and cell wall thickness for both core and bast fibre were in the range 0.736 mm to 1.542 mm, 0.0237 mm to 0.0242 mm, 0.0178 mm, and 0.0025 mm to 0.0029 mm respectively. The morphological indices for core and bast fibres were; 10.54 to 12.58, 0.35 to 5.81, 32.21 to 67.43 and 78.83 to 78.90 for coefficient rigidity, runkel ratio, felting power, and coefficient flexibility respectively. It was observed that the best pulp yield was obtained with 1:10 (w/v) solid to liquid ratio of 2 M NaOH solution at digestion time of 90 minutes. The papers produced were examined using Scanning Electronic Microscope (SEM). The finding of this study revealed that bast fibre of S. Officinarum plant holds greater promise as a sustainable alternative source for papermaking than the core fibre.

Sugarcane Bagasse, Bast Fibre, Core Fibre, Paper, Pulp yield

1. A. F. Aderounmu and E. A. Adelusi. Axial and Radial Variation of Fibre Characteristics of Bambusa Vulgaris. Journal of Scientific Research and Reports, 2019, 24(4): 1-8. ISSN: 2320-0227 [Google Scholar] [Crossref]

2. H. Afra, M. Yousefi, and T. Nishino. Comparative effect of mechanical beating and nanofibrillation of cellulose on paper properties made from bagasse and softwood pulps," Carbohydrate Polymers, 2013, 97(2) 725-730. [Google Scholar] [Crossref]

3. S.D. Asagekar, and V.K. Joshi. Characteristics of sugarcane fibres. Indian Journal of Fibre & Textile Research 2014, 39(2):180-184 [Google Scholar] [Crossref]

4. I Bektas, A Tutus and H Eroglu. A Study of the Suitability of Calabrian Pine for Pulp and Paper Manufacture. Turk. J. Agri. For. 1999, 23 (3): 589-597. [Google Scholar] [Crossref]

5. Z. Chen, J. Yi, and D. Feng. Preparation method of corn stalk fibre material and its performance investigation in asphalt concrete. Sustainability 2019, 11(15), 40-50. [Google Scholar] [Crossref]

6. H.O. Chibudike, N.A. Ndukwe, N.I. Obi, O.A. Adeyoju and E.C. Chibudike. MEA Pulping of Sugarcane Bagasse: Effect of Fiber Morphology and Beating Treatment on Properties of Furnished Paper. American Journal of Innovative Research and Applied Sciences. 2020, ISSN 2429-5396 [Google Scholar] [Crossref]

7. G. Daniel, A Lamesa, and G. Degnechew. Investigation of Fibre Properties of Eucalyptus Globulus grown in FartaWoreda as Potential Source for Pulp and Paper Making, Amhara National Regional State, Ethiopia". Research Square Platform LLC. 2022, DOI: 10.21203/rs.3.rs-2093328/v1 [Google Scholar] [Crossref]

8. Z.T Egbewole. Investigation into selected wood quality indices of plantation grown Sterculiasterigera. Masters Research Submitted in the Department Forest Resource Management University of Ibadan, 2004, 178. [Google Scholar] [Crossref]

9. Z.T Egbewole, PO Omoake and OJ Rotowa. Evaluation of fibre quality of Saccharum officinarum (sugarcane bagasse) as a raw material for pulp and paper production. NSUK Journal of Science and Technology, 2015, 5: (2): 142 – 149 [Google Scholar] [Crossref]

10. D.O. Ekhuemelo, and A.M. Udo. Investigation of Variations in the Fibre Characteristics of Moringa Oleifera (Lam) Stem for pulp and paper production. International Journal of Science and Technology. 2016, 5(1): 19-20 [Google Scholar] [Crossref]

11. D. O. Ekhuemelo, V. O. Aidoko and E.T. Tembe. Evaluation of pulp and paper making potentials of FicusExasperataVahl in Makurdi, Nigeria. South Asian Journal of Biological Research. 2018, 1(1): 61-78 [Google Scholar] [Crossref]

12. A.M. El-Sayed, K.H. Hamad, Y. Eid, A. Alaa and A. Mohsen. Production of Paper Using Chemical Pulping Process of Sugarcane Bagasse. International Journal of Industry and Sustainable Development. 2022, 3(1) :57-65 [Google Scholar] [Crossref]

13. P.M. Gopal, N.M. Sivaram, and D. Barik. Energy from Toxic Organic Waste for Heat and Power Generation. Paper Industry Wastes and Energy Generation from Wastes. Woodhead Publishing Series. 2019, Chapter 7: 83-97 doi.org/10.1016/B978-0-08-102528-4.00007-9 [Google Scholar] [Crossref]

14. H. Kirci. Pulping industry. KTU Faculty of Forest Press, No:86, Trabzon 2006 [Google Scholar] [Crossref]

15. M.A. Mahmud and F.A. Rahman. Sugarcane bagasse - A source of cellulosic fibre for diverse applications. J. Heliyon 2021, doi: 10.1016/j.heliyon.2021.e07771 [Google Scholar] [Crossref]

16. A.A. Mayowa (2018) Pulping of Non-Woody Biomass. http://dx.doi.org/10.5772/intechopen.79749 [Google Scholar] [Crossref]

17. SA Noah. Fundamentals of Pulp and Paper Manufacture. Fasco Publishers. Ibadan. 2009, 181pp. [Google Scholar] [Crossref]

18. B. E. Obiora, C.A. Jonah, C. E. Ikenna and N. Christian. Sustainable production and consumption of paper and paper products in Nigeria. 2019, 8:53; doi:10.3390/resources8010053 [Google Scholar] [Crossref]

19. A.O Oluwadare and Z.T Egbewole. Wood Quality Studies in Plantation Grown Steculia (Steculiasetigera) in the Guinea Savannah, Nigeria. Research Journal of Forestry. 2008, 2: 22-33. [Google Scholar] [Crossref]

20. M.A. Onilude. Pulp and Paper Industry: A Neglected Goldmine in Nigeria. Inaugural Lecture 2010/2011. University of Ibadan, Nigeria. 2011 [Google Scholar] [Crossref]

21. A. O. Osadare and J. S. Udohitinah. Fibre Characteristics of some Nigerian Raw Materials for Long Fibre Pulp Production. In: Forestry for Urban and Rural Development in Nigeria, Oduwaiye, E. A. (Ed). FAN 23rd Conference, 1993, Pp: 132-138 [Google Scholar] [Crossref]

22. O. J. Rotowa, Z. T. Egbewole, and P. O. Omoake. Evaluation of Fibre Quality of Bambusa Vulgaris (Bamboo) as a Raw Material for Pulp and Paper Production. Production & Agriculture Tech, (2015, 11 (2): 188-202 ISSN: 0794-521 [Google Scholar] [Crossref]

23. N.A Sadiku, A.O. Oluyege, and B. Ajayi. Fibre dimension andChemical Characterisation of Naturally Grown Bambusa Vulgaris for Pulp and Paper Production. J. Bamboo and Rattan. 2018, 15(1-4): pp. 33-43. [Google Scholar] [Crossref]

24. A.O Sotannde. Preliminary Investigation into the Fibre Characteristics of Thaumatococcusdanielli. MSc. dissertation submitted to the Department of Forest Resource Management for the award of Bachelor of Forestry Degree, University of Ibadan. 2000, Pp 120. [Google Scholar] [Crossref]

25. Y. Li and X-Q. Dai Biomechanical Engineering of Textiles and Clothing. Woodhead publishing. 2006, ISBN 978-1-84569-052-6 [Google Scholar] [Crossref]

26. R. Young, R. Kundrot and D. Tillman. Pulp and Paper, in Encyclopedia of Physical Science and Technology, Third Edition ed., United States of America, Academic Press, 2003, 249-265. [Google Scholar] [Crossref]

27. ASTM International (American Society for Testing and Materials): Specific gravity of wood and wood -base materials designated, Method b, volume by Immersion, (D 2395-69); Standard method of tests for water solubility Method A and B, (D1110-68); ash, (D1102-72); one percent caustic soda solubility, (D1109-72), and moisture in wood, (D1101-77). [Google Scholar] [Crossref]

28. Technical Association of Pulp and Paper Industry (TAPPI). Acid insoluble lignin in wood and pulp Designated T22 om-98.169 (1998). [Google Scholar] [Crossref]

• Wind Turbine Design for Low Wind Speed Applications: Advancing Renewable Energy Systems Through Wind Tunnel Experiments
• Fast Identification for Evidences in Crime Scene with Macroscopic Properties and Portable Techniques
• Evaluating the Impact of Hello Interval Timer on OSPF Performance for Real-Time Applications Using OPNET
• The Algorithmic Fortress: Ai-Powered Cybersecurity and Anti-Fraud in The Future of Fintech
• Accident Detection on Curved Roads Using Infrared Sensors in Hilly Regions A Case of Chadoora Tehsil, Badgam (J&K)